(050) 809 2007
Tesla model s 3 x y


Tesla diagnostic
Tesla FSD
Tesla Root
Education Courses
09.01.2022

loki tesla Diagnostics Tesla vehicles
loki tesla buy diagnostics


model s 
model x
model 3

reset valet
reset pin to drive 
reset pin speed limit

rail on 
d gear 

tesla car config 
install firmware 
install maps
change map region 
redeploy 


in valet mode auto:

  • does not connect to wireless networks
  • does not open the front trunk
  • does not open the glove compartment
to remove the valet mode, you need to know the 4-digit Pin code or just press the reset valet button
also one button reset pin to drive
also one button reset pin speed limit

There is a cid on button to turn on the screen
for diagnostics, you need to switch the car to the following modes: factory mode; developer mode
on new firmware, the entrance to the factory occurs through reset all data
factory mode remains after mcu reboot
developer mode after reboot mcu crashes
After enabling these modes, you can read alerts (errors)
errors in the block are also decoded


to work with loki you need to connect
connect the LAN wire Fakra to the car


2) turn on the raspberry pi 3 model b hotspot
3) enter wifi password LOKI XX:

wfCeCVk4wkGFgWbh



Working with Configuration
LOKI has the ability to work with vehicle configuration
Tesla model s
Model X

WARNING! BEFORE WORKING WITH THE CONFIGURATION, DO BACKUP
CONFIGURATION FROM A VEHICLE SO IN THE CASE OF AN INCORRECT CHANGE
THE POSSIBILITY TO RETURN TO THE ORIGINAL SETTINGS.

The machine must have FACTORY MODE activated.
We connect to the LAN port under the monitor and select the IP address 192.168.90.125,
after which we can work in the CAR CONFIG window.

Select Model 3 GW in the program

To check the connection with the gateway, click on "TEST GW CONNECTION",
the appearance of "OK, CONNECT ACTIVE" indicates that everything is fine and possible
continue on.
CAR CONFIG window
(to work with jumper and Tegra)
The configuration window contains two windows:
CURRENT CAR CONFIG - current vehicle configuration
CONFIG OPTIONS - values ​​that this or that item can take
configuration

WARNING There is no TEST GW CONNECTION button in CONFIGURATION!

You can use READ CONFIG to test the connection. If successful
By reading the configuration parameters, it can be concluded that the connection is active.

The configuration file is edited like a regular text file,
but at the same time if you try to add non-existent parameters or
non-existent parameter values, the program will not let you write a new file
configuration!
After the necessary values have been changed, press "WRITE CONFIG"

The program offers to confirm the selected changes and, if the changes are correct,
then after clicking "OK" the following notification will appear

REMEMBER! YOU DO ALL WORK WITH THE CONFIGURATION PERSONALLY
RESPONSIBILITY!


Installing navigation maps
Changing the map region 

WARNING! Before installing maps, you need to change the CONFIG maps to EU.
WARNING! Before installing the cards, make sure that the vehicle is not
downloads / installs the firmware and whether the alarm clock "hangs" in it. Ate some of this
present - you need to wait until the firmware is fully installed.
WARNING! To install car maps, you need to connect to WiFi, and wait
about 10 minutes to make sure that the car does not suddenly download the firmware at the moment
installation of cards.

1. Installation of maps is performed in the FIRMWARE tab
2. The map file itself is selected
3. Make sure that the "INSTALL AS MAP" checkbox is checked
4. Click on the start installation button
On firmware up to 2020.24, the following inscription will appear in the log, after that in the car
loading of maps will start: that file is not being served
On firmware after 2020.24, the following inscription will appear in the log, after that in the car
loading of maps will start: start map installation


Installing firmware (mark as MCU)


you will be able to set the navigation yourself
select map file
check that the installation of the map will be (mark as map)
you will be able to install the firmware yourself (mark as MCU)

you can independently change the map region 
for this you need to go to the section Model 3 GW
car config tab
set EU map region

192.168.90.100 to test the connection
192.168.90.101 - for connection through the MCU1 dashboard (Tegra) and for work with
configuration in MCU2 (Intel)
192.168.90.103 - for connection through the autopilot port
192.168.90.125 - for connection via diagnostic LAN under the monitor and for operation
with configuration in MCU1


You can check work LOKI:

by connecting anydesk to our pc

You can buy safely with Escrow.com



I from Ukraine Kiev and I love my country

you will like loki price


Telegram: 
@xboxoneboss1

https://t.me/xboxoneboss1

 



Все новости

Заявка